QuickBend: Conduit Bending

Great app. One thing they could add is concentric bends. If that was added it would literally have every possible option for bending with any type of bender. Other than that, it has made years of pipe bending so much easier. I recommend it to everyone. Thanks for such a great app. Well worth the price -IBEW Local 73 member

The app works great, I was a bit hesitant to buy it at first, but it soon made me a believer. We all know that the deducts of older side winders or on any bender fades over time, this app has them all down and it has the travel measurements too!.. it also works if you have no signal.

rolled offset doesn't have degree option anymore

I use an android and a coworker of mine has an iphone. For instance when we put in parameters for a kick 90 using a greenlee 854. His gives the measurement to start the bend and mine only shows the center of the bend. Between his and mine there was about a 6 inch difference. So i would have to figure out the start. There is no options to change this on my android so this would be my only dislike, otherwise its great.

I bought this app in 2019. Now you are telling me that I didn't purchase it on the store and I need to repurchase it

This is by far the best app I have ever used for bending pipe. Super helpful when needing multiple bends with a cut/thread mark for rigid. The fact that it is fractionally accurate is incredible. BEST APP PURCHASE EVER!

I've tried 3 or 4 different bending apps. This is by far the best. It's a great reference for those things I haven't done often, and to make sure I'm understanding the Ugly's book when it comes to figuring out where my marks go. Thanks much. -4th year AW LU 176

It's been useful to an extent so far, I don't concern myself with offsets & such as that however but mostly downloaded the app for segmented 90s & I had a tank that had a nominal diameter of 338inches & when I divide by 2 to get the radius it's too high , the app only goes up to 120" radius max unless there's something I'm missing? Using standard greenlee smart bender but wish they could remove the cap. My coworker has the same app ,looks slightly different & doesn't have the cap why ?

I'm an industrial electrician, I haven't had to make a segmented or consecutive bend before. I had a stick of 1" RMC and need a 180° bend 26" diameter at a height of 2'. I set up a greenlee 555 for the job and tested the bend on a stick of 3/4 IMC as a test "Didn't have many 1" sticks". Needless to say I forgot to switch to 3/4 for the greenlee so my deduct was 2" off. But the diameter was great.

Really cool, but should add some kind of slide, double tap, hold, etc lock feature to the protractor. I think it'd be way too easy to accidentally reset the zero when trying to use it.

My favorite tool in my tool box. This app is basically cheating. I've been able to make some incredible installs with this app. This app really becomes useful when you want to thread rigid straight and bend it to the right lengths "mathematically". If nothing else, I use it to reference bender specs like take up, radius and gain.

I've only ever paid for two apps. This is one of them. 100% worth it. Many people compliment my conduit work, and I always tell them about this app! It saved me countless of hours and dollars of material. I only use multiple bends feature and it works perfectly! The only thing I'd recommend for a change is the digital level should have a small defined button to actually reset it. I continuously reset the level when handling the phone.

Plenty of information. Very thorough. That problem is the very 1st measurement I used off this app according to its bend marks on a simple 1 1/2" offset on 854 smart bender were off. Ugly pipe bend. Had to do way too much work on top of the bend to make it work. This leads me to believe that most minimum distances between bends on benders have not been field tested. This was supposed to save me time, but now I'm back to my manual methods.

The apple version of this app is laid out differently as it has features that the Android version doesn't have as far as i can tell. The main thing I want is where to put my mark, and what the app tells me is the distance to the center of the bend. I have to use the right deduction, and this information is only available for common angle degrees. For anything else i have to use the multibend. You cannot use multibend at the same time as the other functions requiring a lot of manual entry.

terrible this app gives you wrong measurements and does not do correct 3 bend sattles. absolute garbage app

I hate that I can't change the "between bends" and "first bend" on the comp 90 bends. That would have been so useful. I love the protractor, although I wish It would be able to zero out itself at 0 0⁰ instead of me having to do it manually with a level. I'm still learning, how to bend and how to use the app. The main thing is being able to change more aspects of the bends like I had mentioned in the first paragraph, but this app is pretty good.

Please update your android version of the app and bring it on par with the Apple version.... Especially seen as we paid for it. Thank you ( 9th of June 2025) thanks for the UI for Android I saw it this morning. 👍🏻

new UI is trash, as a tradesman I want simple functionality, don't sacrifice functionality for looks. wish I had not updated the app.

This is a fantastic app. Years ago I made a chart for all the benders I've used on the job which included info about the start of bend, the centerline radius, the deductions and the minimum distance from the end of conduit to the shoe. It also had the formula for the developed length of a bend. I don't have to use that chart anymore. This app does it for me.

I would give 5 stars if that stupid slider BS wasn't a thing. I can't find out how to disable it and just switch to a normal numpad input. I dont wanna fiddle around with plus or minus whatever or sliding my finger around. I wanna type the dang number and be done. Otherwise, it is near perfect for 1" and 3/4. Haven't tried bigger sizes yet but it's a calculator, so I'm sure they'll be correct.

I been in the trade 24yrs and have needed a tool like this hundreds of times. Congrats on taking all the thinking out of my job. My green helper can now bend pipe better then the old timers and I love it! Thanks again. You guys hit a home run with this app!

Even if you only bend conduit a couple times a year for work or home, this app is a MUST. If you can read a ruler and have this app you are now a conduit master. Got everyone at work to download it. Thanks a million.

Pay for the premium version. Unless you only bend conduit all day and memorize this stuff, it will be well worth it. I’ve been able to move away from doing lazy easy bends and have greatly decreased the number of j boxes and pull points I need to install.

I want to make a 3 point saddle with 3 rise with 1/2 emt, using hand bender. My angles are 45 degrees for the center and 22.5 for the outside bends. Why does the app say to make the ‘distance from the center of one bend, to the next bend’ 8 and 5/8 inches when all charts say 7 and 1/2?

This app is great and unlike any of the others. All of the benders you can choose from have precise given measurements and almost completely takes knowing the formulas to a point of uselessness. Great job!